Main components of the coal mill
Release date:
2021-07-06
1. Bearing section
A hydrostatic pressure test is conducted on the bearing liner cooling system, with the test pressure set at 0.6 MPa and maintained for 1 hour; the system is deemed合格 if no leakage is observed during this period. The high-pressure oil chamber passages are flushed, after which an oil pressure of 25 MPa is applied and held for 20 minutes; the system is considered合格 if no leakage occurs. The main bearing base plates must be lifted into position within the alignment box. Since the coal mill has two bearing base plates, their machined surfaces must be aligned on the same horizontal plane; a level is used for calibration, ensuring that the levelness is controlled within 0.1 mm/m. For verifying the centerlines of the two bearing base plates, the string‑line method may be employed, with the deviation kept within 1 mm. The main bearing is then installed onto the base plates, ensuring uniform contact between the bearing and the base plate; at regular intervals, a 0.1‑mm feeler gauge is used to check the contact gaps, and any areas with excessive gaps are appropriately adjusted. Finally, the bearing liners, saddle seats, and other related components are thoroughly cleaned, lubricant is applied, and the bearing liners are placed into the saddle seats.
2. Rotating parts
Rotate the left-hand helical tube to the fixed end cover and the right-hand helical tube to the movable end cover. For checking the mating clearance, use a 0.55 cm feeler gauge. When installing the end covers and the cylinder flanges, apply lead-based grease to the mating surfaces to enhance contact; then mount the fixed and movable end covers onto the cylinder body and secure them with M30 bolts. Next, verify the circumferential shoulder‑to‑shoulder clearance and make appropriate adjustments to ensure that the two cross‑point measurements are equal. Finally, tighten the bolts and drive in the cotter pins. After assembling the cylinder and end covers, lift the entire assembly into position on the main bearing liner, ensuring that there is no binding between the inner bore of the main bearing and the end‑cover journal during scraping and lapping. Once the transmission components have been installed, calibrate the clearance between the oil‑slinger on the movable end‑cover journal and the bearing liner; this clearance must exceed 20 mm. Use a spirit level to check the horizontal alignment of the rotating assembly.
3. Transmission Unit
On the one hand, check the lateral clearance between the pinion and the gear; based on the gear’s position, select an appropriate center distance for installing the pinion, and verify the parallelism deviation of the pinion and gear’s centerlines, ensuring that the error does not exceed 0.15 mm per meter. In addition, combine this with an inspection of the lateral clearance to thoroughly examine the meshing condition of the two gears, confirming that the clearance remains within the range of 1.24 to 2.19 mm. The following methods can be used to measure tooth‑side clearance: ① Use a feeler gauge to measure the inter‑tooth gap: rotate the pinion so that its driving tooth flank is in contact with the driven gear’s tooth flank, then insert the feeler gauge into the driven flank to measure the tooth‑side clearance; repeat the measurement at both ends of the tooth flank. If the gears are installed correctly, the two readings should be identical. ② Employ lead wire: place the lead wire between the two gear flanks at both ends of the tooth width; as the gears turn slowly, the lead wire will be compressed by the meshing action. Then use a micrometer to measure the thickness of the flattened portion of the lead wire. ③ For certain equipment where there is insufficient space near the bearing housings of the pinion and gear, making it difficult to insert a feeler gauge, mount a dial indicator on the top of the pinion’s tooth flank and rotate the pinion in both forward and reverse directions. The gear clearance is determined by summing the dial indicator’s readings. On the other hand, assess the contact ratio of the pinion–gear mesh. This can be done using the color‑transfer method: apply paint to the gear’s tooth surface, covering approximately ten teeth in succession; then rotate both gears and return to the painted positions to observe the locations where the opposing gear’s tooth surface has been stained. If the gears are properly meshed, the stain marks will be evenly distributed along the middle of each tooth flank. If the stain marks are concentrated toward the upper half of the tooth flank, it indicates that the center distance is too large; if they are concentrated toward the lower half, the center distance is too small; and if the stains appear at the tooth flank edges, the gears must be adjusted and aligned.
Previous page
Next page
Previous page
Next page
Haixin Power Equipment Manufacturing (Nantong) Co., Ltd.
Consultation
Address
No. 66, Oujiangnan Road, Haimen Subdistrict, Haimen District, Nantong City, Jiangsu Province
Scan to access the mobile version!
Copyright © 2026 Haixin Power Equipment Manufacturing (Nantong) Co., Ltd.